Milwaukee 5380-21 Manual Del Operador página 3

SPECIFICATIONS
Tool
Volts No Load
Cat. No. AC A No Load RPM BPM
Low 0 - 1500 24,000
5380-21 120 9
High 0 - 3500 56,000
EXTENSION CORDS
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example, a 14
gauge cord can carry a higher current than a 16
gauge cord. When using more than one extension
cord to make up the total length, be sure each cord
contains at least the minimum wire size required. If
you are using one extension cord for more than one
tool, add the nameplate amperes and use the sum
to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors,
be sure it is marked with the suffi x "W-A" ("W"
in Canada) to indicate that it is acceptable for
outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired by
a qualifi ed person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
Nameplate
Amperes 25' 50' 75' 100' 150'
0 - 2.0 18 18 18 18
2.1 - 3.4 18 18 18 16
16
3.5 - 5.0 18 18 14
5.1 - 7.0 18 16 14 12
7.1 - 12.0 16 14 12 10
12.1 - 16.0 14 12 10
16.1 - 20.0 12 10
* Based on limiting the line voltage drop to fi ve volts
at 150% of the rated amperes.
READ AND SAVE ALL
INSTRUCTIONS FOR FUTURE USE.
Capacities
Drill Only Hammer-Drill
Twist Drill Twist Drill Carbide Tipped
Bit (Wood) Bit (Steel) Percussion Bit (concrete)
1/2" 5/8"
Functional Description
6
5
4
3
1. Side handle
2
2. Clamping lever
3. Depth gauge
4. Chuck
5. Speed selector
1
6. Hammer/Drill lever
7. Lock button
8. Trigger
9. Forward/Reverse lever
ASSEMBLY
WARNING
To reduce the risk of injury,
always unplug tool before attaching
or removing accessories or making adjust-
ments. Use only specifi cally recommended
accessories. Others may be hazardous.
WARNING To reduce the risk of injury,
always use a side handle when using
this tool. Always brace or hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
16
Setting the Depth Gauge
14
1. Press in the clamping lever.
12
12
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the rod.
3. Release the clamping lever.
WARNING
To reduce the risk of injury
do not grasp the bit while the chuck is rotat-
ing or while the bit is falling from the chuck.
WARNING
To prevent personal injury,
always remove the chuck key from the
chuck after each use.
4
Installing Bits into Keyed Chucks
Be sure that the shank of the bit and the chuck
jaws are clean. Dirt particles may cause the bit
to line up improperly. Do not use bits larger than
the maximum recommended capacity of the drill
because gear damage or motor overloading may
result. For best performance, be sure that the bits
3/4"
are properly sharpened before use.
1. Unplug the tool.
2. Open the chuck jaws wide enough to insert a bit.
Allow the bit to strike the bottom of the chuck.
Center the bit in the chuck jaws and tighten the
jaws by hand to align the bit.
7
WARNING
9
always unplug tool before attaching or remov-
ing accessories or making adjustments. Use
8
only specifi cally recommended accessories.
Others may be hazardous.
WARNING
wear safety goggles or glasses with side
shields.
WARNING
keep hands and cord away from the bit and
all moving parts.
Selecting Action
MILWAUKEE Hammer-Drills have two settings:
drilling and hammer-drilling.
1. For drilling, turn the hammer-drill lever towards
the drill symbol .
2. For hammer-drilling, turn the hammer-drill lever
towards the hammer symbol .
NOTE: To engage the hammering mechanism,
maintain pressure on the bit. When pressure on the
bit is released, the hammering action will stop.
Using Forward/Reverse Lever
The forward/reverse lever can only be adjusted
when the trigger is not pressed. Always allow the
motor to come to a complete stop before using the
forward/reverse lever.
1. For forward (clockwise)
rotation, push the for-
ward/reverse lever to the
left (when viewed from
the back of the tool) as
shown.
2. For reverse (counterclockwise) rotation, push the
forward/reverse lever to the right (when viewed
from the back of the tool) as shown. Allow the
motor to come to a full stop before reversing.
NOTE: When hammer-drilling, use the tool in for-
ward rotation (clockwise) only.
3. Place the chuck key into
each of the three holes
in the chuck, turning it
clockwise to tighten the
chuck securely.
NOTE: Never use a
wrench or means other
than a chuck key to tight-
en or loosen the chuck.
4. To remove the bit, insert
the chuck key into one of the holes in the chuck
and turn it counterclockwise.
OPERATION
Selecting Speed
To reduce the risk of injury,
Allow the tool to come to a complete stop before
changing speeds. Changing speeds while the tool
is running could damage the tool.
1. For low speed (up to 1500 rpm), turn the
speed selector to position 1.
2. For high speed (up to 3500 rpm), turn the
To reduce the risk of injury,
speed selector to position 2.
Starting, Stopping & Controlling Speed
1. To start the tool, pull trigger.
2. To stop the tool, release trigger.
To reduce the risk of injury,
3. To vary the speed, increase or decrease pres-
sure to trigger. The further the trigger is pulled,
the greater the speed.
Locking Trigger
The lock button holds the trigger in the ON position
for continuous full speed use.
1. To lock the trigger, hold in the lock button while
pulling the trigger. Release the trigger.
2. To unlock the trigger, pull the trigger and release.
The lock button will pop out.
Operating
Position the tool, grasp the handles fi rmly and pull
the trigger. Always hold the tool securely using both
handles and maintain control. This tool has been
designed to achieve top performance with only
moderate pressure. Let the tool do the work.
If the speed begins to drop off when drilling deep
holes, pull the bit partially out of the hole while the
Forward
tool is running to help clear dust. Do not use water to
settle the dust since it will clog the bit fl utes and tend
to make the bit bind in the hole. If the bit should bind,
a built-in, non-adjustable slip clutch activates. If this
Reverse
occurs, stop the tool, free the bit and begin again.
5
Loosen
Tighten