Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Free the end of the wire and cut off the bent end making
sure it has no burr.
Sharp end of the wire can hurt.
Rotate the wire spool clockwise and thread the end of
the wire into the wire feeder as far as the Euro socket.
Adjust force of pressure roll of the wire feeder properly.
Adjustments of Brake Torque of Sleeve
To avoid spontaneous unrolling of the welding wire the
sleeve is fitted with a brake.
Adjustment is carried by rotation of its screw M8, which
is placed inside of the sleeve frame after unscrewing the
fastening cap of the sleeve.
21. Fastening cap.
22. Adjusting screw M8.
23. Pressing spring.
Turning the screw M8 clockwise increases the spring
tension and you can increase the brake torque.
Turning the screw M8 counterclockwise decreases the
spring tension and you can decrease the brake torque.
Adjusting of Force of Pressure Roll
Force
Pressure force is adjusted by turning the adjustment nut
clockwise to increase force, counterclockwise to
decrease force.
If the roll pressure is too low the roll will slide on the wire.
If the roll pressure is set too high the wire may be
deformed, which will cause feeding problems in the
welding gun. The pressure force should be set properly.
Decrease the pressure force slowly until the wire just
begins to slide on the drive roll and then increase the
force slightly by turning of the adjustment nut by one
turn.
Inserting Electrode Wire into Welding
Torch
Connect the proper welding torch to the Euro socket, the
rated parameters of the torch and of the welding source
shall match.
Remove the gas diffuser and contact tip from the
welding torch.
Set the wire feeding speed in the position of about
10m/min by the WFS knob [2].
Switch the Cold Inch / Gas Purge switch [15] in the
position "Cold Inch" and keep in this position until the
WARNING
WARNING
electrode wire leaves the contact tip of the welding torch.
Take precaution to keep eyes and hands away from the
end of the torch while feeding wire.
Once the wire has finished feeding through the welding
gun turn the wire supply off before replacing to contact
tip and gas diffuser.
Welding methods
Welding with MIG / MAG method
To begin welding process with MIG/MAG method in
manual mode you should:
•
Switch ON the machine which supplies the wire
feeder.
•
Insert the electrode wire into the torch using "Cold
Inch" switch [15].
•
Check gas flow with "Gas Purge" switch [15].
•
According to selected welding mode and material
thickness set the proper welding voltage with knob
[3] and the wire feeding speed with WFS knob [2].
•
Obeying the appropriate rules, you can begin to
weld.
Welding with MMA (SMAW) method
The LF33S wire feeder enable Manual Metal Arc welding
process that uses a consumable electrode coated in flux
by cooperating with CC (constant current) power
sources like DC 400, DC 655 or V350 PRO.
In order to start welding process with MMA method you
should:
•
Connect the wire feeder to over mentioned CC
power source by the combined cable.
•
Connect welding torch into output socket [9].
•
Switch the power source in CC mode.
•
Set required welding current by adjusting knob
[3].
•
Obeying appropriate rules you can begin to
weld.
LF33S compatibility functions with source
DC 400
LF 33S Knob [3] Settings before welding
CC
CV
V
No
√
A
√
No
LF 33S Display during and after welding
CC
CV
V
√
√
A
√
√
Changing Driving Rolls
The wire feeder is equipped with drive rolls for the wire
of 1.0 and 1.2mm. For others wire sizes, is available the
proper drive rolls kit (see chapter Accessories for
ordering the desired kit). Below the drive rolls
replacement procedure:
•
Switch off the machine which supplies the wire
feeder.
•
Release the pressure roll lever [24].
•
Unscrew the fastening cap [25].
•
Open the protection cover [27].
•
Change the drive rolls [26] with the compatible ones
A-4
WARNING
WARNING
LF33S + CC/CV source
DC 655
CC
CV
No
√
√
No
On source
CC
CV
√
√
√
√
V 350 PRO
CC
CV
No
√
No
CC
CV
√
√
√
√
Tabla de contenido
