Maintenance And Care; Disposal Information; Declaration Of Conformity; Exemption From Liability - Flex MXE 1000 Instrucciones De Funcionamiento Originales

Switching the mixer on and off
Brief operation without engaged switch rocker
(Figure F)
 First press the starting lockout (1.). Then press and hold
down the switch (2.). Release switch interlock (3.).
 To switch off, release the switch (4.).
Continuous operation with engaged switch rocker
(Figure G)
 First press and hold down the starting lockout (1.) and
then the switch (2.).
 To lock into position, hold down the locking button and
release the switch (3.). Release switch interlock (4.).
To switch off, briefly press and release the switch (5.).
NOTE!
If the mixer does not turn after switching on:
– Switch the power tool off (release lock by pressing switch).
– Rotate the mixer paddle manually by 45°.
– Switch the power tool back on again.
CAUTION!
Following a power failure, the switched on power tool does
not restart.
Operating instructions (Figure H)
 After it has been switched off, the mixer runs on for a
short time.
 If the rotating mixer paddle strikes a surface, it could
cause a jolt.
 Only switch on the tool after the mixer paddle has been
immersed in the product to be mixed. When doing this,
slowly press the switch and wait until the tool has
reached maximum speed.
 When taking a break from work, place the tool down on
the rests.
Overload protection
In the event of a short and extreme overload, the overload
protection device prevents damage to the motor by switching
the tool off automatically.
For further information on the manufacturer's products go to
www.flex-tools.com.

Maintenance and care

WARNING!
Before performing any work on the mixer, pull out the mains
plug.
Cleaning
 Regularly clean the power tool and ventilation slots.
 Regularly blow out the housing interior and motor with dry
compressed air.
 Clean the mixer paddle straight after use. Do not allow the
mixed product to dry on.
Gear
NOTE
Do not loosen the screws on the gear head during the warranty
period. Failure to comply with this requirement will invalidate
any claims under the manufacturer's warranty.
11
MXE 1000/MXE 1002/MXE 1200/MXE 1202/MXE 1602
Repairs
Repairs may be carried out by an authorised customer
service centre only.
Spare parts and accessories
Mixer paddles for different applications and other
accessories can be gleaned from the manufacturer's
catalogues.
Exploded drawings and sparepart lists can be found on our
homepage: www.flex-tools.com

Disposal information

WARNING!
Render disused power tools unusable by removing the
power cord.
EU countries only.
Do not dispose of electric power tools in
the household waste!
In accordance with the European Directive 2012/19/
EU on Waste Electrical and Electronic Equipment and its
incorporation into national law, used power tools must be
collected separately and recycled in an environmentally friendly
manner.
NOTE!
Please ask your dealer about disposal options.

-Declaration of Conformity

We declare under our sole responsibility that the product
described under page 5 conforms to the following standards or
normative documents:
EN 62841 according to the provisions of Directives 2014/30/
EU, 2006/42/EC, 2011/65/EU.
Responsible for technical documents:
FLEX-Elektrowerkzeuge GmbH, R & D
Bahnhofstrasse 15, D-71711 Steinheim/Murr
06.09.2019
FLEX-Elektrowerkzeuge GmbH
Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative are not liable for
any damage and lost profits due to interruption in business
caused by the product or by an unusable product. The
manufacturer and his representative are not liable for any
damage which was caused by improper use of the power
tool or by use of the power tool with products from other
manufacturers.