Installation Location; Electrical Requirements; Safety Instructions; Using The Remote Control Unit - Technibel Climatisation MCW1B5XA Instrucciones De Uso

INSTALLATION LOCATION

We recommend this air conditioner to be installed
G
properly by qualified installation technicians in
accordance with the installation instructions provided
with the unit.
WARNING
Do not install this air conditioner where there are
G
fumes or flammable gases, or in an extremely humid
space such as a green house.
Do not install the air conditioner where excessively
G
high heat-generating objects are placed.
G Do not install the air conditioner where the
atmosphere is extremely damp or humid (e.g.
greenhouse or laundry) it could be wetted by drops
of water (i.e. in laundries).
ELETRICAL REQUIREMENTS
Before installation, check that the voltage of the electric
G
supply in your home or office is the same as the voltage
shown on the nameplate.
All wiring must conform to the local electrical codes.
G
Consult your dealer or a qualified electrician for details.
Each unit must be properly grounded with a ground (or
G
earth) wire or through the supply wiring.
Wiring must be done by a qualified electrician.
G

SAFETY INSTRUCTIONS

Read this booklet carefully before using this air
G
conditioner. If you still have any difficulties or
problems, consult your dealer for help.
This air conditioner is designed to give you
G
comfortable room conditions. Use this only for its
intended purpose as described in this Instruction
Manual.
WARNING
G Never use or store gasoline or other flammable vapor or
liquid near the air conditioner. It is very dangerous.
Never install electrical equipment, which is not
G
protected with IPX1 protection (protection against
vertical water drop), under the unit.
The manufacturer assumes no responsabilities if the
G
safety regulations or local codes are not observed.
CAUTION
Never use the power main switch to start or stop the
G
air conditioner: always use the ON/OFF button on the
remote control unit or the selector switch on the unit.
Do not stick anything into the air outlet of the air
G
conditioner. This is dangerous because the fan is
rotating at high speed.
Do not let children play with the air conditioner.
G
Do not cool the room too much if babies or invalids
G
are present.

USING THE REMOTE CONTROL UNIT

HOW TO INSTALL BATTERIES
Remove the lid in the rear part of the remote control
G
unit.
G Insert two AAA alkaline batteries of 1,5 V-DC.
Make sure the batteries point in the direction marked
in the battery compartment.
The batteries last about six months. Depending on how
G
much you use the remote control unit.
Remove the batteries if you do not use the remote control
unit for more than one month.
Press the +, -, SET and CLEAR buttons together after
batteries replacement.
(This operation allows you to reset correctly all the
programs. The remote control unit is to be set up again).
Replace the batteries when the remote control unit lamp
fails to light, or when the air conditioner does not receive
the remote control unit signals.
The batteries of the remote control contain polluted
G
substances exhausted batteries must be disposed
according to the laws in force.
TEMPERATURE SENSOR SELECTOR
Under normal conditions the room temperature is detected
G
and checked by the temperature sensor placed in the air
conditioner.
Press the remote control I FEEL button to activate the
G
temperature sensor placed in the remote control. This
function is designed to provide a personalised environment
by transmitting the temperature control command from the
location next to you. Therefore, in using this function, the
remote control should always be aimed, without
obstruction, at the air conditioner.
NOTE
The remote control unit sends
the temperature signal to the
air conditioner regularly at two
minute intervals. If the signal
from the remote control unit
stops for more than five
minutes due to some troubles,
the air conditioner will switch to the temperature sensor
which is built into the indoor unit and controls the room
temperature. In these cases, the temperature around the
remote control unit may differ from the temperature
detected in the air conditioner position.
OPERATION WITH THE REMOTE CONTROL UNIT
CAUTION
Check that the circuit breaker on the power panel is turned
ON and the the STANDBY lamp is light up.
When using the remote control unit, always point the unit
transmitter head directly at the air conditioner receiver.
HOW TO TURN ON THE AIR CONDITIONER
Press the ON/OFF button to turn the air conditioner on.
The indicator OPERATION will light up, indicating the unit
is in operation.
4
REMOTE CONTROL UNIT
DISPLAY
GB