Makita LM02 Manual De Instrucciones página 5

5. Use a power source with the voltage specified on the
nameplate of the charger.
6. Do not charge the battery cartridge in presence of
flammable liquids or gases.
7. Do not expose charger to rain or snow.
8. Never carry charger by cord or yank it to disconnect
from receptacle.
9. After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever
disconnecting charger.
10. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
11. Do not operate charger with damaged cord or plug -
replace them immediately.
12. Do not operate or disassemble charger if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified serviceman.
Incorrect use or reassembly may result in a risk of
electric shock or fire.
13. The battery charger is not intended for use by young
children or infirm persons without supervision.
14. Young children should be supervised to ensure that
they do not play with the battery charger.
15. Do not charge battery cartridge when temperature is
BELOW 10°C (50°F) or ABOVE 40°C (104°F).
16. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Charging (Fig. 1)
Charge the battery cartridge with the Makita charger
before use.
1. Plug the battery charger into the proper AC voltage
source. The charging light will flash in green color.
2. Insert the battery cartridge so that the plus and minus
terminals on the battery cartridge are on the same
sides as their respective markings on the charger.
3. When the battery cartridge is inserted fully, the
charging light will change from green to red and
charging will begin. The charging light will remain lit
steadily during charging.
4. When the charging light changes from red to green,
the charging cycle is complete.
5. After charging, unplug the charger from the power
source.
NOTE:
• The battery charger is for charging Makita battery
cartridge. Never use it for other purposes or for other
manufacturer's batteries.
• If you charge a battery cartridge from a just operated
tool or a battery cartridge which has been exposed to
direct sunlight or heat for a long time, the charging light
may flash in red color. If this occurs, wait for a while.
Charging will begin after the battery cartridge cools.
• If the charging light flashes alternately in green and
red, charging is not possible. The terminals on the
charger or battery cartridge are clogged with dust or
the battery cartridge is worn out or damaged.
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
(Fig. 2)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around
you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Lighting up the lamp (Fig. 3)
CAUTION:
• Do not look in the light or see the source of light
directly.
• Push the switch to light up the light. To turn off, push
the switch again.
NOTE:
• When remaining battery capacity becomes lower,
light turns off automatically. So you should charge
the battery cartridge soon.
• Operating time may be shortened according to
environments and battery conditions.
OPERATION
Clip (Fig. 4)
User can carry the light with hands free by hooking the
clip on a belt.
Attaching flexible leg (Fig. 5, 6 & 7)
Slide the C-shaped portion of the flexible leg over the light
in the direction of the arrow.
Hold the flexible leg securely in place by fitting the raised
portion of the flexible leg in the hole of the clip.
Using flexible leg (Fig. 8, 9)
CAUTION:
• Do not wind the flexible leg over a part of body
such as hand or arm to use the flash light.
This may cause the tool to drop, resulting in the flash
light damage, personal injuries etc.
• Do no carry the flash light by flexible leg.
This may cause the flash light to drop, resulting in the
flash light damage, personal injuries etc.
• Do not wind the flexible leg over moving objects
such as bicycle to use the flash light.
Vibration may cause the flash light to drop, resulting in
the flash light damage, personal injuries etc.
By attaching the flexible leg to the light, the light can be
set on or fixed at various locations for hands-free lighting.
e.g. 1) The light can be set on the surface of a
workbench or the like by standing the light on the
flexible leg.
5