Tabla de contenido
5. Before use
Mounting the bow-type handle (Fig. 1)
If there are screws fixed to the mounting points, remove
these first. Then, remove the shear protector and put the
bow-type handle from the front (as shown in Fig. 1) over
the shearing system, and put it into the relief of the hedge
shears' housing. (If necessary, pull the lower ends of the
handle slightly apart.) Take care that you do not squeeze
the two parts of the bow-type handle.To fasten the bow-
type handle screw the two included screws through the
openings in the handle into the threaded holes of the
housing and fasten them tightly.
Protection shield (Fig. 2)
If screws are fastened to the bottom plate, remove these.
Fasten the hand protector with the two included screws
to the bottom plate.
Power connection
The machine can only be connected to a single-phase
a.c. current connection. The machine is protectively
insulated in accordance with classification II of VDE
0740. Before using the machine ensure that the mains
current agrees with the operating voltage data on the
machine's identification plate.
Power Circuit Breaker:
Machines which will be used in different outside
locations must be connected to a Power Circuit
Breaker.
Securing the power supply cable (Fig. 5)
Only use cables (extension flex) that are approved for
outdoor use. The cable diameter must be equal to or bigger
than 1.5mm² for cable lengths up to 75m.
Extension flexes with a length of more than 30m reduce
the machine's output.
6. Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet
hedges!
Check the hedge trimmer flex and its connections
before each and every use for visible signs of
damage (disconnect the power plug)! Do not use a
faulty flex.
Gloves:
Protective gloves must be worn when using the
hedge trimmer.
7. Switching the hedge shears on/off
When switching the hedge shears on take a safe stand.
These hedge shears have a two-hand safety switch. To
switch the hedge shears on the bar switch in the handle
(A) and the grip switch of the bow-type handle (B) must
be pushed down. To switch the device off let go of both
switches. The motor already stops if one of the two
switches is released.
8. Maintenance
Always disconnect the plug from the power socket
before commencing any work on the machine.
Important: Always clean and oil the blades after
prolonged use of the hedge trimmer. This will greatly
affect the life of the equipment. Damaged cutting units
must be properly repaired immediately. Clean the
shearing blades with a dry cloth or – in case of heavier
dirt – with a brush. Attention: Danger of injury!Oiling
of the blades should ideally be carried out using an
environmentally friendly lubricant (Fig. 6).
Sharpening of the blades
The blades generally do not need servicing and do
not require resharpening if used correctly. In order to
prevent injuries caused by the blades when not in use,
the sharpened cutting blade should be covered by the
blade cover (Fig. 4). The blades cannot be sharpened by
the user without opening the equipment and the safety
mechanism. Resharpening of the blades can therefore
only be carried out at a specialist workshop.
Changing the blades
Only correct installation of the blades will guarantee
problem-free operation and function of the above
mentioned safety feature of the blades. Changing of
the blades should therefore only be carried out at a
specialist workshop.
9. Holding the hedge trimmer when in use
(Fig. 7)
This equipment will enable you to cut or trim bushes and
hedges easily and comfortably.
Trimming of hedges
-
Young shoots are best cut in a scythe move ment.
-
Older and stronger hedges are best cut in a sawing
movement.
-
Branches, which are too thick for the hedge trimmer,
should be cut with a saw.
-
Sides of hedges should be cut upwards in a taper.
In order to achieve an even height
-
Fix a guide line at the required height.
-
Cut evenly over this guide line.
Expanded working height: If you want to reach higher
or if you to above your head's height (see Fig. 8), you
should take care of the following:
Attention: Take care to have a secure and safe standing
(Fig.3)
position when working with your hedge shears in order
to avoid slipping and injury. Always keep the shearing
blades away from your body.
10. Optimum safety
The 5 special features two-hand safety switch, quick
blade stop, protective cover, blade safety rail and
impact protector are fitted to provide the hedge
trimmer with optimum safety features.
GB-4
Tabla de contenido
