General Safety Information For Power Tools - IKRA HHSI 5246 Instrucciones De Manejo

manufacturer / supplier is not liable for any injury and/
or damage arising from inappropriate use. This risk
is the sole responsibility of the user.Appropriate use of
the machine also includes adherence to the operating
instructions and compliance with the servicing and
maintenance instructions.
Always keep the instruction manual close at hand during
operation!

4. General safety information for power tools

Attention! Read all instructions contained herein. Fail-
ure to observe the following instructions may result in
electric shock, burns and/or severe injury. The term
'power tool' used in the following includes both mains-
operated tools (with mains supply) and battery-operated
tools (without mains supply).
KEEP THESE INSTRUCTIONS CAREFULLY!
1) Working area
a) Keep your working area clean and tidy. Untidy
and poorly lit working areas may lead to ac-
cidents.
b) Do not operate the tool in potentially explosive
environments containing combustible fluids,
gases or dusts. Power tools generate sparks that
may ignite dusts or fumes.
c) Keep children and other persons away when
you are operating the power tool. Distractions
may result in the operator loosing control over
the tool.
2) Electrical safety
a) The mains plug of the power tool must fit into
the mains socket. The plug must not be modi-
fied in any way. Do not use adapter plugs/con-
nectors in combination with tools with protec-
tive earthing. Unmodified plugs and fitting sockets
reduce the risk of electric shock.
b) Avoid physical contact with earthed surfaces
as pipes, heaters, ovens and refrigerators.
There is an increased risk of electric shock if your
body earthed.
c) Keep the tool out of the rain. The penetration
of water into a power tool increases the risk of
electric shock.
d) Do not use the cable to carry or hang up the
tool or to pull the plug out of the socket. Keep
the cable away from heat, oil and sharp edges
or moving parts of the tool. Damaged or tan-
gled cables increase the risk of electric shock.
e) When operating a power tool outdoors, use
exclusively extension cables that are approved
for outdoor-use. The use of an extension cable
that is suitable for outdoor use reduces the risk of
electric shock.
f) If the operation of a power tool in a moist envi-
ronment cannot be avoided it is highly recom-
mended to use a residual current device (RCD).
The use of an RCD reduces the risk of electric
shock.
3) Personal safety
a) Always pay attention to what you do and apply
reasonable care when working with a power
tool. Do not use the tool when you are tired or un-
der the influence of medication, drugs or alcohol.
When working with power tools even a short mo-
ment of inattentiveness may result in severe injury.
b) Wear personal protection equipment and always
wear eye protection (safety goggles). Wearing
personal protection equipment as a dust mask, non-
slip safety shoes, safety helmet or ear protectors
(depending on the type and use of the tool) reduces
the risk of injury.
c) Avoid unintentional operation. Make sure that
the switch is in 'OFF' position before pulling the
plug from the mains socket. When carrying the
tool with your finger on the on/off switch or connect-
ing the tool to the mains supply with the switch in
'ON' position, this may result in accidents.
d) Remove adjustment tools or wrenches and the
like before you switch the tool on. A wrench or
another tool that is inside or on a turning part of the
tool may cause injury.
e) Do not overestimate your abilities. Take care
of a safe footing and keep your balance at all
times. This will allow you to better control the tool
in unexpected situations.
f) Wear suitable clothes. Do not wear wide clothing
or jewellery. Keep your hair, clothes and gloves
clear of all moving parts. Loose clothing, jewellery
or long hair may get caught in moving parts.
g) If dust extraction/collection devices are pro-
vided make sure that they are connected and
used properly. The use of these devices reduces
hazards caused by dust.
4) Careful handling and use of power tools
a) Do not overtax the power tool. Use the power
tool intended for your type of work in each case.
The use of the suitable power tool within the stated
range of performance makes working more effec-
tive and safer.
b) Do not use a power tool with a damaged switch.
A power tool that cannot be switched on or off any
more is dangerous and must be repaired.
c) Pull the mains plug out of the socket before you
adjust a tool, change accessories or put the tool
aside. This precaution avoids the unintentional start
of the tool.
d) Store power tools out of the reach of children.
Do not allow persons to use the tool if they are
not familiar with the tool or these instructions.
Power tools are dangerous if used by inexperienced
persons.
e) Thoroughly maintain your power tool. Check
whether moving parts are working properly and
are not jamming/sticking, and whether parts
are broken or otherwise damaged in a way that
affects the function of the tool. Have damaged
parts repaired before using the tool. Many ac-
cidents are the result of poorly maintained power
tools.
GB-2