Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Appendix
Troubleshooting
P
o r
b
e l
m
•
N
o
p
o
w
r e
• Unit cannot be operated.
• Remote control unit does not
operate.
• Picture is cut off/with sidebar
screen.
• Strange color, light color, or color
misalignment
• Power is suddenly turned off.
•
N
o
o s
u
n
d
58
POWER on the remote control unit.
•
C
h
e
k c
f i
o y
u
r p
s e
e s
d
• Is the AC cord disconnected?
• Has the power been turned on?
• External influences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after first turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Is the equipment to be operated by the remote control unit set correctly? Press TV
to set the remote control unit to the setting for operating the TV.
• Are batteries inserted with polarity ( e , f ) aligned?
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated near the remote control sensor?
• Is the image position correct?
• Are screen mode adjustments such as picture size made correctly?
Pages 21 to 22 and 25
• Adjust the picture tone.
• Is the room too bright? The picture may look dark in a room that is too bright.
• Is the sleep timer set?
• Check the power control settings.
• The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
•
s I
c
o
n
n
c e
o i t
n
o t
o
h t
r e
c
o
• Is the volume too low?
• Have you pressed MUTE on the remote control unit?
• Check the audio output of the connected external equipment. Is the volume too
low or muted?
• When external equipment is connected via an HDMI cable, you may need to
configure the audio to be output through the HDMI cable.
• When audio is not output from external equipment connected to the PC IN or HDMI
1 terminal, check the "Audio Select" setting.
• Even when external equipment is connected using an HDMI-certified cable, an audio
cable connection may be required depending on the type of equipment and the
media being played back. In this case, in addition to connecting an HDMI-certified
cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo mini jack cable to the
AUDIO IN terminal and set "Audio Select" to "HDMI+Analog".
• When connecting a PC via an HDMI-certified cable, check the following:
- Is the audio output of the PC configured correctly? Check the audio output
settings and output audio format in Sound Properties on the PC.
Only PCM format audio can be output. Compressed audio (with a sampling rate
of 32kHz, 44.1kHz, or 48kHz) and DTS format audio cannot be output.
- Depending on the board, only video signals may be output. In this case, in
addition to connecting an HDMI-certified cable to the HDMI 1 terminal, connect a
Ø 3.5 mm stereo mini jack cable to the AUDIO IN terminal and set "Audio Select"
to "HDMI+Analog".
Page 28
• If you are using a DVI-HDMI conversion cable to connect external equipment to the
TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable is for video only.
Connect a Ø 3.5 mm stereo mini jack cable to listen to the audio.
- Is HDMI 1 being used? When the TV is connected to another HDMI terminal, the
audio and video are not output together even if a Ø 3.5 mm stereo mini jack cable
is connected to the shared AUDIO IN terminal for PC IN and HDMI 1.
- Check the "Audio Select" setting. Set "Audio Select" to "HDMI+Analog".
P
o
s
s
b i
e l
S
l o
t u
o i
n
Page 8
Page 17
Pages 22 and 47
Pages 25 and 26
Page 19
Pages 26
m
p
o
n
e
n
s t
c
o
r r
c e
? t
Pages 12 to 16 and 43
Page 19
Page 28
Page 17
Page 9
Page 19
Page 28
Page 28
Capítulos
Tabla de contenido
Solución de problemas
