Functional Description - Makita ELM4121 Manual De Instrucciones

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Assembling the handle
1. Unload the upper handle from the main unit of the
machine.
► Fig.1: 1. Upper handle
2. Loosen the thumb nuts.
► Fig.2: 1. Thumb nut
3. Widen the handle outside a little, then raise the
handle, then insert the protrusions of the handle into the
holes, and then tighten the thumb nuts.
► Fig.3: 1. Handle 2. Protrusion 3. Hole 4. Thumb nut
4.
Attach the upper handle by inserting the levers
from the outside of the handle, and then tighten the nuts
with the wrench to secure the handle.
► Fig.4: 1. Lever 2. Nut
5. Secure the cords with the clamps as shown in the
figure.
► Fig.5: 1. Clamp
Installing the grass basket
1. Attach the pipes of the grass basket to the frame.
► Fig.6: 1. Pipe 2. Frame
2.
Open the rear cover.
► Fig.7: 1. Rear cover
3. Insert the grass basket from the front side through
the inside of the handle, and then hook the grass basket
onto the rear side of the machine.
► Fig.8: 1. Grass basket
► Fig.9
To remove the grass basket, perform the installation
procedure in reverse.
Connecting extension cord
WARNING:
When connecting the extension
cord to the power plug of the machine, make sure
that the switch lever is released and the cord is
unplugged from the power supply.
WARNING:
Do not connect or disconnect the
extension cord with wet hands.
NOTICE:
When connecting the extension cord to
the power plug of the machine, be sure to insert it
fully into the socket.
When connecting the extension cord, hook it over the
hook on the handle as shown in the figure to prevent
inadvertent unplugging by excessive strain on the plug.
For ELM4121/ELM4620
► Fig.10: 1. Hook 2. Extension cord
For ELM4621
► Fig.11: 1. Hook 2. Extension cord
Attaching the mulching attachment
1.
Open the rear cover, and then remove the grass
basket.
► Fig.12: 1. Rear cover 2. Grass basket
2. Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
► Fig.13: 1. Mulching attachment 2. Lever
Attaching the discharge attachment
For ELM4620/ELM4621
1. Open the rear cover, and then remove the grass
basket.
► Fig.14: 1. Rear cover 2. Grass basket
2.
Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
► Fig.15: 1. Mulching attachment 2. Lever
3. Open the right side cover, and then attach the
discharge attachment.
► Fig.16: 1. Discharge attachment 2. Right side cover
NOTICE:
Be sure to insert the discharge attach-
ment until the latch snaps into place.
► Fig.17: 1. Latch
FUNCTIONAL
DESCRIPTION
Adjusting the mowing height
WARNING:
height, unplug the extension cord from the power
supply, and check that the blades have come to a
complete halt.
WARNING:
the mower body when adjusting the mowing
height.
You can adjust the mowing height in the range of 20 mm
to 75 mm. The mowing height can be adjusted in 7 lev-
els (for ELM4121) or 8 levels (for ELM4620/ELM4621).
For ELM4121
► Fig.18: 1. Adjusting lever
For ELM4620/ELM4621
► Fig.19: 1. Adjusting lever
Hold the handle with one hand, and then move the lever
with the other hand.
► Fig.20: 1. Adjusting lever
13 ENGLISH
Before adjusting the mowing
Never put your hand or leg under