SPARKY HeavyDuty MB 2200PA HD Instrucciones De Uso página 11

the initial and any following operation.
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected and dis-
connected to the power supply socket only
when this switch is in OFF position. If the plug
is connected to a receptacle while the power
switch is in the ON position, the power tool
will start operating immediately, which could
cause a serious accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
▪ When using diamond cutting discs, pay atten-
tion that the direction-of-rotation arrow on the
diamond cutting disc and the direction of rota-
tion of the machine (see direction-of-rotation
arrow on the machine head) agree.
▪ Make sure the grinding wheel diameter and
thickness do not exceed the values specified
on the name plate. The peripheral speed in-
dicated on the wheel must not be less than
80 m/s. The wheels must be stored according
the recommendations of the manufacturer.
▪ In case the work area is remote from the pow-
er source, use as short as practicable exten-
sion cord with proper cross-section.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.
SWITCHING ON - SWITCHING OFF
The angle grinder is secured against uninten-
tional switching on.
▪ Switching on: First push forward the auxiliary
button 8 positioned at the bottom of the main
handle, then press ON/OFF switch 7. For
continuous operation switch 7 can be locked
(only for models with index P in the abbre-
viation). In this case while holding switch 7,
press button 8 and then release switch 7.
▪ Switching off: Release switch 7; in case the
switch is locked, first press and then release
that switch.
In case of mains drop-out (or temporary
drop-out for time t > 0.5 s), when the ON/
Original instructions
Off switch is in ON position, the machine
should not operate after supply recovering.
To start operating the machine, first switch
off and then switch on the lever of ON/Off
switch 7.
WHEEL GUARD
WARNING: The wheel guard 3.1 for
grinding wheel or the wheel guard 3.2 for
cutting wheel (for grinding wheel 2.1 or cut-
ting wheel 2.2 accordingly) must always be
mounted on the machine!
WARNING: Before performing the fol-
lowing operations, switch off and unplug the
machine.
Mounting the wheel guard (fig. 1)
- Rotate the black plastic ring (Fig. 2a), so
that the crevice S of the ring coincides with the
groove for the tooth of the fixing lever L.
- Place the wheel guard in non-operating
position (Fig.2a) so that the four teeth coin-
cide with the four grooves in the bearing seat
(Fig.2b).
- Press the fastening lever L (fig.3) to re-
lease it.
- Press the wheel guard down and rotate it
in the necessary operating position (Fig.4).
- Release the fastening lever L to a stable
position in which the wheel guard is fixed (the
fixing lever tooth enters into one of the guard
grooves).
Rotating the wheel guard in a new operat¬ing
position
- Press the fastening lever L (Fig.3) to re-
lease it.
- Rotate the wheel guard to the necessary
operating position.
- Release the fastening lever L to a stable
position in which the wheel guard is fixed (the
fixing lever tooth enters into one of the guard
grooves).
Removing the wheel guard
- Press the fastening lever L (Fig.3) to re-
lease it.
- Rotate the wheel guard in non-operating
position (Fig.2a) so that the four teeth coin-
cide with the four grooves in the bearing seat
(Fig.2b).
- Remove the wheel guard.
9
EN