Chicco Polly Swing Up Instrucciones De Uso página 20

of the seat (Diagram 7).
WARNING: Check that the seat fabric is fitted correctly before us-
ing the swing.
6. Take hold of the connection tubes on the seat frame (component
b) and insert the round shaped end into the slots at the side of
the seat (Diagram 8), making sure that the side hooks on the sun
hood are facing inwards towards the swing. Make sure you hear
the metal pins click into place.
7. To assemble the seat on the frame, slide the oval shaped ends of
the connection tubes into the mobile slots on the X and Y fixtures
(Diagram 9). When you hear the metal pins click into place, it
means the seat is fitted correctly. The assembling of the swing
frame has now been completed.
FITTING THE SAFETY HARNESS
8. Check that the upper harness straps are correctly slotted
through the slots in the fabric, as indicated in the previous para-
graph (point 4).
9. Slide the plastic rings into the slots on the bottom of the fabric
seat.
10. Slide the waist strap through the plastic rings located at the
bottom of the seat. Now use the relative clasps to fasten the
upper harness straps to the waist strap (Diagram 10).
11. Slide the two toothed ends into the buckle on the fabric crotch
strap (Diagram 11). The harness straps can be adjusted to differ-
ent lengths according to your child's build.
12. To assemble the dual tray on the swing, place the ends of the
tray on the side connection fixtures and press until you hear it
click into place.
BOOSTER CUSHION
The swing can be used with a modular booster cushion which has a
section for the body and a headrest cushion.
13. To use the booster cushion, thread the upper harness straps and
the waist strap through the relative slots; now fasten the upper
straps to the waist strap using the relative clasps.
14. Thread the Velcro through the selected fabric slot to fasten the
headrest to the backrest. The headrest can be adjusted to two
different heights to adapt to the various growth phases whilst
guaranteeing comfort and protection.
15. Place the child in the swing and slide the two toothed ends into
the buckle (as seen in Diagram 12).
USING THE SUN HOOD
Polly Swing Up also has a practical sun hood: To assemble it:
16. Grasp the sun hood making sure the side with the slots for the
baby toys is facing the front of the swing.
17. Fasten the sun hood side fixtures to the side hooks on the con-
nection tubes.
18. The position of the sun hood can be adjusted as necessary.
19. To remove the sun hood, gently pull the fixtures towards the
inside of the swing until they are released.
ASSEMBLING AND USING THE REMOTE CONTROL
20. The remote control runs on 2 x 1.5 Volt LR03-AAA batteries and
can be used either attached or detached from the fixture. See
Diagrams 13 and 14.
21. The remote control can be used to:
a) Switch the music and swinging motion ON and OFF;
b) Select 1 of the 4 swing speeds;
c) Select the nature sounds and tunes;
d) Adjust the volume.
SIDE FIXTURE WITH REMOTE CONTROL
22. A battery compartment (Diagram C1) is located inside the fix-
ture X which powers the swing motion. It runs on 4 x 1.5 Volt
LR14 –C batteries.
23. There is a button inside the remote control compartment.
If swing mode is already being used:
a) Press and hold the button for 3 seconds to switch off the
music and the swing motion
If swing mode is turned OFF:
a) Press (quickly) and release the button once to start the
swing motion.
b) Press the button again to select the desired swing speed;
each time the button is pressed it will change the speed
from 1 to 4. On reaching the fastest speed, it will start from
1 speed again.
c) Press and hold the button for 3 seconds to switch off the
electronic mode.
Remember that the button on the remote control fixture is only
used to start and stop the swing motion; it cannot be used to start
the nature sounds or tunes.
24. If the swing motion stops, check whether:
a) The batteries are still working
b) The batteries are fitted correctly
c) The weight of children is appropriate
d) The child is perhaps leaning forwards too much.
VIBRATION BLOCK
25. The swing is fitted with a vibration block (Diagram F3) which
can be activated by turning the knob to the "I" position. The
vibration block runs on 1 x 1.5 volt LR20-D battery.
REPLACING THE REMOTE CONTROL, SIDE FIXTURES AND VI-
BRATION BLOCK BATTERIES
26. To replace the remote control, side fixture and vibration block
batteries; remove the screws from the various battery compart-
ment covers (Diagrams 15 and 16). Fit the new batteries making
sure they are fitted with their poles in the right direction. Now
replace the compartment covers and firmly tighten the screws.
FOLDING AWAY AND TRANSPORT
The swing can be folded up to store or transport it.
27. Press the side buttons on the X and Y fixtures and close the
frame by pulling the front and rear legs towards each other.
(Diagram 17)
WARNING: Never use the sun hood to carry the swing.
*The theme of the removable toys varies according to the colour
coordination chosen.
20
¡I
RI
¡A
TA
TO
FO
DU
N
N
AD
•¡A
at
•¡A
be
pe
• ¡
se
río
•
en
m
• ¡
de
•
sio
cie
ni
• ¡
gu
• ¡
pr
Es
ca
de
cu
• N
es
• N
no
• L
gu
ne
se
cu
to
• A
pr
ra
• N
a