Notes on Safety
Instructions for installation and connection.
Disconnect the battery ground wire during installation and connection.
This car radio can be used for both 2 x 20 or 4 x 7 watts operation. For
this, the corresponding connector box has to be mounted to the car radio.
When drilling a hole, be sure not to damage any vehicle parts (battery,
cable, fuse case, etc.).
The positive cable must have a cross-section of at least 1 mm
is protected by a quick-acting fuse of 10 A.
Note:
By means of the support included in delivery you can mount the set in cars
with a DIN car radio cut-out of 182 x 53 mm, an installation depth of 165
mm and an instrument panel thickness around the fixing clips of 1 - 20
mm, see fig. 1.
For cars with other cut-out dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets. Use enclosed
distance plates only for installation kits of 52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.
When using installation sets for units of 52 mm four distance plates, order
number 8 601 055 056 must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cut-out provided in your car's dashboard
ex factory.
Prepare the car radio DIN cut-out (unlock shelf or dummy cover) or cut
out the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cut-out and check how many of the fixing
strips of the car radio support may be bent.
Note:
Try to bend as many fixing strips as possible.
Insert the support into the cut-out and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Connection overview .................................................................. Fig. 4
Notes on connection ................................................................... Fig. 5
Connection of equalizer and amplifier ......................................... Fig. 6
Connection CD-Player ............................................................ Fig. 7, 8
Loudspeaker connection:
4 speakers (4 Ω/7 W) .................................................................... fig. 9
2 speakers (4 Ω/22 W) ................................................................ fig. 10
2 speakers (4 Ω/22 W) with amplifier ......................................... fig. 11
Depending on the speaker equipment of the respective vehicle either the
2- or 4-channel connector box has to be exchanged (the 2 x 20 watts box
is marked).
Change connecting box
1. Loosen the screw and unlock the top and bottom support springs by
lifting them, see fig. 13.
2. Pull out the connecting box, see fig. 14.
3. Position the connecting box with the sides in the correct position and
parallel to the cabinet, and push it in carefully, see fig. 15.
4. Tighten the screw and hook in the top and the bottom support screw.
5. Replace the fuse of the connecting box.
Important notes!
If these notes are disregarded, there is danger of destroying the
final stages.
Do not connect speaker outputs to ground!
Connection with vehicle's system connector (ISO connector)
For vehicles prefitted with ISO connectors pins 1, 2 and 3 of the ±
connector must always remain free, fig. 4.
GB
2
For Audi and VW models use the adapter cable only.
For Opel models exchange pins 4 and 7 of the ± connector, fig. 4.
Connection with QuickOut installed ex factory
If a car is fitted with QuickOut ex factory (at present Opel), the QuickOut
ex factory has to be removed.
Ground cable.
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
. The unit
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC 12 V)
(ignition)
Connect the positive cable together with distributor to pin 30 (constant
power) or pin 15 (positive line connected via ignition) of the fuse holder
behind the fuse.
Permanent plus connection
(Battery 12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna + )
When connecting a fully automatic motor antenna, use the cable clamp
to fasten the control cable of the motor antenna to the control cable.
Lighting connection (Illumination)
Lighting connection for vehicles with adjustable dashboard lighting (plus-
controlled).
Telephone mute (Low)
If you have connected a car telephone, your car radio will be mutet during
telephone calls.
Telephone mute is not possible if a CDC-M1/M3 is installed in your car.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Using both brackets (see fig. 3), pull the unit out.
Modifications reserved
Notes de sécurité
Instructions de montage et de branchement
Pendant le montage et le branchement des appareils, il convient de
déconnecter le pôle négatif de la battérie.
L'autoradio peut fonctionner en 2 x 20 W ou 4 x 7 W. Ce fonctionnement
n'est possible qu'après le montage du boîtier de raccordement adapté
sur l'autoradio.
Veiller à ce qu'aucun élément de voiture (tel que la batterie, les câbles,
les porte-fusibles) ne soit pas endommagé par le perçage des trous).
La section du câble positif ne doit pas être inférieure à 1 mm
est protégé par l'intermédiaire d'un fusible à déclenchement rapide 10 A.
Note:
A l'aide du support inclus dans le jeu de montage vous pouvez monter
le poste dans des voitures qui disposent d'une découpe DIN de 182 x 53
mm, d'une profondeur de 175 mm et d'une épaisseur du tableau de bord
de 1 - 20 mm autour des éclisses de montage, voir fig. 1.
Blaupunkt livre des jeux de montage spéciaux pour les voitures courantes
avec découpes différentes pour les appareils 50/52 mm. N'utilizer les
platines d'écartement ci-jointes que pour les jeux de montage des
appareils 52 mm.
+12V
per. +12V
+12V
F
2
. L'appareil
