Makita GA7010C Manual De Instrucciones página 5

ENGLISH
(Original instructions)
1 Shaft lock
2 Switch trigger
3 Lock lever
4 Side grip
5 Wheel guard
6 Screw
7 Bearing box
8 Nut
9 Lever
10 Lock nut
11 Depressed center wheel/
Multi disc
SPECIFICATIONS
Model
Depressed center wheel diameter................................................180 mm
Spindle thread ..............................................................................M14
Rated speed (n) / No load speed (n
Overall length ...............................................................................453 mm
Net weight.....................................................................................4.3 kg
Safety class ..................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
2. Operations such as polishing are not recom-
mended to be performed with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
Explanation of general view
12 Inner flange
13 Inner flange 102
14 Lock nut wrench
15 Abrasive disc
16 Rubber pad
17 Wire cup brush
18 Wire wheel brush
19 Abrasive cut-off wheel/diamond
wheel
20 Wheel guard for abrasive cut-off
wheel/diamond wheel
21 Outer flange 78
)...........................................8,400 min
0
GEA010-1
GEB033-3
22 Inner flange 78
23 Dust collecting wheel guard
24 Exhaust vent
25 Inhalation vent
26 Commutator
27 Insulating tip
28 Carbon brush
29 Screwdriver
30 Brush holder cap
GA7010C
-1
/II
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
6. The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of
the power tool will run out of balance, vibrate exces-
sively and may cause loss of control.
7. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged accesso-
ries will normally break apart during this test time.
GA9010C
230 mm
M14
-1
6,000 min
453 mm
4.5 kg
/II
5