Ec Declaration Of Conformity - Husqvarna 953876533 Manual De Instrucciones

BLADE
To remove the blade (19) unscrew the screw
l
(20).
lCheck the conditions of the blade-support (21), the key
(22) and replace any parts which are damaged.
GUARANTEE AND GUARANTEE POLICY
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna Outdoor Products,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge
providing:
a) The fault is reported directly to the Authorised Re-
pairer.
b) Proof of purchase is provided.
c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
d) The failure has not occurred through fair wear and
tear.
e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Husqvarna Outdoor Products.
f) The machine has not been used for hire.
g) The machine is owned by the original purchaser.
h) The machine has not been used commercially.
l This guarantee is additional to, and in no way diminishes
the customers statutory rights.
Failures due to the following are not covered, therefore
it is important that you read the instructions contained in
EC DECLARATION OF CONFORMITY
I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC)
Certify that the Lawnmower:-
Category .......................................................... Electric Wheeled Rotary
Make ................................................................ Husqvarna Outdoor Products
Products Conforms to the specifications of Directive 2000/14/EEC
I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC) Certify
that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum Aweighted
sound pressure level recorded at operator position under free field semi anechoic chamber conditions was:-
I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC)
Certify that a sample of the above product has been tested using ISO 5349 as a guide. The maximum weighted root
mean square value of vibration recorded at operator's hand position was:-
Type of Cutting Device .................................... Rotary Blade
Identification of Series ..................................... See Product Rating Label
Conformity Assesment Procedure ................... ANNEX VI
Notified Body ................................................... NEMKO Spa
Other Directives: .............................................. 98/37/EEC, 2004/108/EEC, 2006/95/EEC
& applicable standards: ................................... EN60555-2:1987, EN60555-3:1987, EN55014:1993, EN55014:1995,
EN836:1997, IEC335-1:1991, IEC335-2-77:1996
Type ...............................................................................A
Version............................................................. .............B
Width of cut.......... .........................................................C
Guaranteed sound power level......................................D
Measured sound power level.........................................E
Sound pressure livel at the ear ......................................F
Vibration of the handle ...................................................G
lWhen reassembling, make sure that the key (22) is cor-
rectly seated in the shaft and that the cutting edges face
in the direction of the engine rotation. The blade screw
(20) must be torqued to 3,7 Kgm (35 Nm).
this Operator's Manual and understand how to operate
and maintain your machine:
Failures not covered by guarantee
- Replacing worn or damaged blades
- Failures as a result of not reporting an initial fault.
- Failures as a result of sudden impact.
- Failures as a result of not using the product in accordance
with the instructions and recommendations contained in
this Operator's Manual.
- Machines used for hire are not covered by this gua-
rantee.
- The following items listed are considered as wearing parts
and their life is dependent on regular maintenance and
are, therefore not normally subject to a valid warranty
claim: Blades, Electric Mains cable, Belt
- CAUTION!
Husqvarna Outdoor Products does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts
or additional parts that are not either manufactured or
approved by Husqvarna Outdoor Products, or by the
machine having been modified in any way..
Technical Manager
Husqvarna Outdoor Products Italia spa
Via Como 72 - 23868 Valmadrera (LC)
ENGLISH - 5