EINHELL TC-SM 2531/2 U Manual De Instrucciones Original página 24

5.2 Assembling the base frame
(Fig. 1, 4a – 4e)
•
Assemble the base frame as shown in Fig.
4a-4e. Attach the parts together using the
screws (a), spring washers (b), washers (c)
and nuts (d). Do not fully tighten the screws
yet.
•
Start with the top cross struts (101) and the
top longitudinal struts (102) followed by the
leg upper sections (105).
•
Next, mount the bottom cross struts (103)
and bottom longitudinal struts (104) along
with the legs (105). Then mount the rubber
feet (106) on the legs.
•
Turn the complete base frame around and
tighten all of the screws.
•
Place the saw on the base frame and fasten
the saw to the frame using the screws (e),
spring washers (g), washers (f) and nuts (h).
5.3 Assembling the saw (Fig. 1-5)
•
To adjust the turntable (17), loosen the lo-
cking screw (14) by approx. 2 turns and push
the lever (33) to release the turntable (17).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14). The saw has locking positions at angles
of - 45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°
and 45°, at which the turntable (17) audibly
clicks into position.
•
To release the saw from its position at the
bottom, pull the fastening bolt (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing the machine head (4) up until the re-
lease lever (3) latches into place.
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
Mount the workpiece support (10) on the
fixed saw table (18).
•
Mount the second workpiece support (10) on
the opposite side of the saw
•
When the locking screw (21) is loosened, you
can tilt the machine head (4) to the left by up
to 45°.
•
Fit the table width extension (26) onto the
workpiece support (10).
•
Fasten the table width extension with the lo-
cking screw (107).
Anl_TC_SM_2531_2_U_SPK9.indb 24 Anl_TC_SM_2531_2_U_SPK9.indb 24
GB
5.4 Precision adjustment of the stop for cros-
scut 90° (Fig. 1, 6-9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the right using
the handle (1).
•
Place the 90° angular stop (y) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally check the position of the pointer (20)
on the scale (19). If necessary, undo the poin-
ter (20) with a Philips screwdriver, set it to the
0° position on the scale (19) and retighten the
retainer screw.
•
No stop angle included.
5.5 Precision adjustment of the stop for miter
cut 45° (Fig. 1, 6-9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking screw (21) and move the
machine head (4) all the way to the left using
the handle (1), until it coincides at 45°.
•
Place the 45° stop angle (z) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
No stop angle included.
5.6 Adjusting the miter angle on the machine
head (Fig. 3, 14)
•
Loosen the locking screw (21).
•
Hold the machine head (4) by the handle (1).
•
The machine head can now be tilted conti-
nuously to the left.
•
Angles to the left: 0-45°
•
Re-tighten the locking screw (21).
5.7 Adjusting the movable stop rail (Fig. 1, 5)
•
Caution! This saw is equipped with a remo-
vable stop rail (34) which is screwed to the
fixed stop rail (11).
•
To make angle and miter cuts, the movable
stop rail must be adjusted to prevent collision
with the saw blade.
•
For miter and angle cuts to the left, the left
stop rail must be moved outwards. Undo the
locking screw on the movable stop rail and
pull the rail back so far that a collision with the
saw blade can be ruled out. Prior to every cut,
retighten the locking screws of the stop rail.
- 24 -
09.09.2019 15:00:05 09.09.2019 15:00:05