EINHELL TE-CC 250 UF Manual De Instrucciones Original página 24

6.2 Fitting the base frame (Fig. 1, 3-5)
•
Open the lock on the base frame by pressing
the lever (35) inwards.
•
Let the legs of the base frame latch into posi-
tion again in the swung-out position.
•
Use the axle screws (f), washers (g), spacer
sleeve (h) and nuts (i) to fasten the wheels
(31) to the base frame.
•
Use the screws (e) and washers (d) to fasten
the machine to the base frame.
•
The base frame is fitted with an adjustable
rubber foot (13). You can use it to compensate
for small unevenness on the work surface.
6.3 Fitting and adjusting the splitter
(Fig. 6a, 9)
Danger! Pull out the power plug.
•
Set the blade (4) to max. cutting depth, move
to 0° position and lock in place.
•
Dismantle the saw blade guard (see 6.4).
•
Take out the table insert (see 6.5).
•
Undo the fastening screw (19).
•
Insert the splitter between the mounting plate
(29) and the splitter counter bearing (30).
•
The distance between the splitter and the
saw blade should be approx. 3-8 mm.
•
Retighten the fastening screw and fit the table
insert.
6.4 Fitting/removing the saw blade guard
(Fig. 6b, 1c)
•
Mount the saw blade guard on the splitter so
that the screw (15) fits through the hole (18)
in the splitter.
•
To dismantle, proceed in reverse order.
Warning! The saw blade guard must always
be lowered over the workpiece before you
begin to cut.
6.5 Changing the table insert (Figure 7)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the 1 countersunk head screws (17).
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.6 Fitting/replacing the saw blade (Fig. 8)
Warning! Pull out the power plug.
•
Take out the table insert (see 6.5).
•
Undo the screw (36) by placing one open-
ended spanner on the nut and another open-
ended wrench on the outer flange (40) to
Anl_TE_CC_250_UF_SPK9.indb 24 Anl_TE_CC_250_UF_SPK9.indb 24
GB
apply counter-pressure.
•
Turn the nut in the direction of rotation of the
saw blade
•
Remove the outer flange and remove the old
saw blade from the shaft and the inner flange.
•
Clean the flanges before fitting the new saw
blade.
•
Fit the new saw blade by following the above
instructions in reverse and then retighten it.
Important! Check that the saw blade turns in
the correct direction. The cutting direction of
the teeth must point in the running direction,
meaning forwards.
•
Refit the table insert and the saw blade guard
(see 6.4, 6.5)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the saw
blade, check that the saw blade guard (2)
opens and closes again in accordance with
requirements. Also check that the saw blade
(4) spins freely in the saw blade guard (2).
•
Warning! Every time that you change the saw
blade (4), check to see that it spins freely in
the table insert (6) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(6) immediately whenever it is worn or dama-
ged (see 6.4).
•
Warning! The work to change and align the
saw blade (4) must be carried out correctly.
6.7 Connection for dust extractor (Fig. 2, 10)
The machine can be connected to a dust extrac-
tor (the extractor adapter set with suction hose is
not included and is available as an accessory):
•
Connect the dust extractor to the extractor
adapter (16).
•
Also, an extraction hose can be connected
to the saw blade guard. To do so, remove the
cap from the saw blade guard, then fit the
extraction hose.
- 24 -
15.10.2019 15:25:12 15.10.2019 15:25:12