EINHELL TE-SM 36/210 Li Manual De Instrucciones Original página 34

6.6 Miter cut 0°- 45° and turntable 0°- 45° (Fig.
1-4, 20)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
If required, dismantle the clamping device
(8) or mount on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.4).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described under points
5.5 and 6.2.
•
Cut as described in section 6.3.
6.7 Limiting the cutting depth (Fig. 21)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the
knurled nut on the screw (27). Turn the screw
(27) in or out to set the required cutting depth
and then retighten the knurled nut on the
screw (27).
•
Check the setting by completing a test cut.
6.8 Sawdust bag (Fig. 8)
The saw is equipped with a sawdust bag (22).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom.
6.9 Replacing the saw blade (Fig. 1, 22)
•
Danger! Remove the rechargeable battery
before you replace the blade.
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Press the spindle locking system (5) with
one hand while positioning the combination
key (42) on the flange bolt (31) with the other
hand. The spindle locking system (5) enga-
ges after no more than one rotation.
•
Now, using a little more force, slacken the
flange bolt (31) in the clockwise direction.
•
Turn the flange bolt (31) right out and remove
the washer (33) and the outer flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange bolt (31), washer
Anl_TE_SM_36_210_Li_Solo_SPK9.indb 34 Anl_TE_SM_36_210_Li_Solo_SPK9.indb 34
GB
(32), outer flange (33) and inner flange.
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the
saw blade, check that the saw blade guard
(6) opens and closes again in accordance
with requirements. Also check that the saw
blade (7) spins freely in the saw blade guard
(6).
•
Warning! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (52) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(52) immediately whenever it is worn or da-
maged. To do so, undo the recessed head
screws in the table insert (52) and take the
table insert out of the turntable (17). To fit
the new table insert (52), proceed in reverse
order.
•
Warning! The work to change and align the
saw blade (7) must be carried out correctly.
6.10 Transport (Figs. 1-4)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Press the machine head (4) downwards and
secure with the retaining pin (25). The saw is
now locked in its bottom position.
•
Carry the machine by the transport handle
(9).
•
To set up the equipment again, proceed as
described in section 5.2 + 5.3.
6.11 Operating the laser (Figs. 12, 23)
Switching on: Move the On/Off switch (36) to the
" " position to switch on the laser (35). A laser
line is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
Switching off : Move the On/Off switch (36) to the
"OFF" position.
- 34 -
21.06.2019 12:37:13 21.06.2019 12:37:13