Makita 4112HS Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Wing bolt
2 Base
3 Cutting depth
4 Clamping nut
5 Wheel guard
6 Switch trigger
7 Lock lever
8 Shaft lock
9 Socket wrench
SPECIFICATIONS
Model
Wheel diameter
Max cutting capacity
–1
No load speed (min )
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting tracks in concrete walls or
cutting in ferrous materials or concrete drainage chan-
nels with a diamond wheel but without using water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
ANGLE CUTTER SAFETY WARNINGS
Safety Warnings Common for Abrasive Cutting-Off
Operations:
1. This power tool is intended to function as a cut-
off tool. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
4
Explanation of general view
10 Flange
11 Ring
12 Wheel
13 Flange
14 Hex bolt
15 Notch
16 Cutting line
17 Commutator
18 Insulating tip
4112S
305 mm
100 mm
3,500
648 mm
11.4 kg
2.
3.
4.
5.
GEA010-1
6.
7.
GEB042-2
19 Carbon brush
20 Dust cover
21 Screwdriver
22 Brush holder cap
23 Dust nozzle
24 Elbow joint
25 Hose
4112HS
305 mm
100 mm
5,000
648 mm
11.4 kg
/II
Operations such as grinding, wire brushing, pol-
ishing are not recommended to be performed
with this power tool. Operations for which the
power tool was not designed may create a hazard
and cause personal injury.
Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of
the power tool will run out of balance, vibrate exces-
sively and may cause loss of control.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing
an accessory, position yourself and bystanders away from the plane of the rotating accessory
and run the power tool at maximum no-load
speed for one minute. Damaged accessories will
normally break apart during this test time.
4114S
355 mm
125 mm
3,500
675 mm
12.8 kg