Declaration Of Conformity - Bosch GKS 160 Professional Instrucciones De Servicio

Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given
period of work should also take into account the times
when the tool is switched off and when it is running
but not actually doing the job. This may significantly
reduce the exposure level over the total working
period.

Declaration of Conformity

We declare under our sole responsibility that this
product is in conformity with the following standards
or standardization documents: EN 60745 according
to the provisions of the directives 89/336/EEC,
98/37/EC.
Dr. Egbert Schneider
Senior Vice President
Engineering
11.10.2006, Robert Bosch GmbH, Power Tools Division
D-70145 Leinfelden-Echterdingen
Assembly
Mounting/Replacing the Saw Blade
Before any work on the machine itself, pull
the mains plug.
When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching the
saw blade.
Only use saw blades that correspond with
the characteristic data given in the operating
instructions.
Do not under any circumstances use grind-
ing discs as the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can be
found at the end of this manual.
Removal of the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the
machine on the face side of the motor housing.
• Press the spindle lock button 4 and keep it
pressed.
The spindle lock button 4 may be actuated
only when the saw spindle is at a standstill.
Otherwise, the power tool can be damaged.
• With the Allen key 6, unscrew the clamping bolt 18
turning in rotation direction
1 609 929 J94 • 6.11.06
Dr. Eckerhard Strötgen
Head of Product
Certification
.
• Tilt back the retracting blade guard 12 and hold
firmly.
• Remove the clamping flange 19 and the saw blade
20 from the saw spindle 22.
Mounting the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the
machine on the face side of the motor housing.
• Clean the saw blade 20 and all clamping parts to
be assembled.
• Tilt back the retracting blade guard 12 and hold
firmly.
• Place the saw blade 20 on to the mounting flange
21. The cutting direction of the teeth (direction or
arrow on saw blade) and the direction-of-rotation
arrow on the blade guard 17 must correspond.
• Mount the clamping flange 19 and screw in the
clamping bolt 18 turning in rotation direction
Observe correct mounting position of mounting
flange 21 and clamping flange 19.
• Press the spindle lock button 4 and keep it
pressed.
• With the Allen key 6, tighten the clamping bolt 18
turning in rotation direction
torque is between 6–9 Nm, which corresponds to
hand tight plus ¼ turn.
Adjusting the Riving Knife
(see figure B–C)
Before any work on the machine itself, pull
the mains plug.
Always work with the riving knife, except
when carrying out plunge cuts. The riving knife
prevents jamming of the saw blade while sawing.
Adjustment is carried out at minimal cutting depth,
see "Adjusting the Cutting Depth", page 20.
It is best to place the machine on the face side of the
blade guard 17.
Loosen the clamping lever 24, pull the saw away from
the base plate 14 and then tighten the clamping lever
24 again.
Loosen screw 23, adjust the riving knife 13 to the
measure shown in the figure and tighten screw 23
with a tightening torque between 8–9 Nm.
Disassembly/Assembly of the Riving Knife
For disassembly of the riving knife 13, unscrew the
screw 23 and remove the riving knife 13.
For assembly, insert the riving knife 13 and tighten it
with the screw 23. Afterwards, check the adjustment
of the riving knife as described previously.
.
. The tightening
English | 19