DeWalt DW083 Manual De Instrucciones página 2

Locking Pendulum
The DW083 is equipped with a locking pendulum mechanism. This feature is only activated when
the laser is switched off. When the power on knob is rotated to the ON position, the pendulum will
be released from the locked position and self level.
Using the Laser
The beams are level or plumb as long as the calibration has been checked (see Field Calibration
Check) and the laser beam is not flashing (see Out of Tilt Range Indicator).
The tool can be used to transfer points using any combination of the three beams.
INTEGRATED MAGNETIC PIVOTING BRACKET
The DW083 has a magnetic pivoting bracket (G) permanently attached to the unit. This bracket
allows the unit to be mounted to any upright surface made of steel or iron using the magnets (H)
located on the back of the pivoting bracket. Common examples of suitable surfaces include steel
framing studs, steel door frames and structural steel beams. Position the laser on a stable surface.
CAUTION: Do not stand underneath the laser when it is mounted with the magnetic
pivoting bracket. Serious personal injury or damage to the laser may result if the laser falls.
The pivoting bracket also provides floor clearance of approximately 1¾" (44.5 mm) which aids in
the installation of steel framing track.
OUT OF TILT RANGE INDICATOR
The DW083 laser is designed to self-level. If the laser has been tilted so much that it cannot level
itself (> 4° tilt), it will flash the laser beam (Fig. 4). The flashing beam indicates the tilt range has been
exceeded and IS NOT LEVEL (OR PLUMB) AND SHOULD NOT BE USED FOR DETERMINING OR
MARKING LEVEL (OR PLUMB). Try repositioning the laser on a more level surface.
USING THE LASER WITH ACCESSORIES
The laser is equipped with a 1/4" x 20 female thread on the bottom of the unit. This thread is to
accommodate current or future D WALT accessories. Only use D
E
use with this product. Follow the directions included with the accessory.
WARNING: Since accessories, other than those offered by D
this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,
only D WALT recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your local dealer or
authorized service center. If you need assistance in locating any accessory, please contact D
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
9258) or visit our website: www.dewalt.com.
LEVELING THE LASER
As long as the tool is properly calibrated, this tool is self-leveling. It is calibrated at the factory to
find plumb as long as it is positioned on a flat surface within 4° of level. No manual adjustments
must be made.
MAINTENANCE
To maintain the accuracy of your work, have the laser checked often to make sure it is properly
calibrated. See Field Calibration Check.
Calibration checks and other maintenance repairs may be performed by D
When not in use, store the laser in the kit box provided. Do not store your laser at temperatures
below -5 ˚F (-20 ˚C) or above 140 ˚F (60 ˚C).
Do not store your laser in the kit box if the laser is wet. The laser should be dried first with a soft
dry cloth.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth. Although these parts are solvent resistant,
NEVER use solvents. Use a soft dry cloth to remove moisture from the tool before storage.
Field Calibration Check
CHECKING ACCURACY – PLUMB
Checking the plumb calibration of the laser can be most accurately done when there is a
substantial amount of vertical height available, ideally 25' (7.5 m), with one person on the floor
positioning the laser and another person near a ceiling to mark the dot created by the beam on
the ceiling (Fig. 5). It is important to conduct a calibration check using a distance no shorter than
the distance of the applications for which the tool will be used.
1. Start by marking a point on the floor.
2. Place the laser so that the down beam is centered on the point marked on the floor.
3. Allow time for the laser to settle to plumb and mark the center of the beam created by the
up beam.
4. Turn the laser 180° as shown (Fig. 6), making sure that the down beam is still centered on
the point previously marked on the floor.
5. Allow time for the laser to settle to plumb and mark the center of the dot created by the up
beam.
If the measurement between the two marks is greater than shown below, the laser is no longer in
calibration.
Ceiling Height
25' (7.5 m)
12' (3.5 m)
CHECKING ACCURACY - LEVEL
Checking the level calibration of the laser unit requires two parallel walls at least 20' (6 m) apart.
It is important to conduct a calibration check using a distance no shorter than the distance of the
applications for which the tool will be used.
1. Place unit 2"–3" (5–8 cm) from first wall, facing the wall (Fig. 7).
2. Mark the beam position on the first wall.
3. Turn the unit 180˚, and mark the beam position on the second wall (Fig. 8).
4. Place the unit 2"–3" (5-8 cm) from the second wall, facing the wall (Fig. 9).
5. Adjust the height of the unit until the beam hits the mark from step 3.
6. Turn the unit 180˚, and aim the beam near the mark on the first wall from step 2 (Fig. 10).
7. Measure the vertical distance between the beam and the mark.
8. If the measurement is greater than the values shown below, the laser must be serviced at an
authorized service center.
Distance Between Walls
25' (7.5 m)
50' (15 m)
75' (23 m)
Troubleshooting
THE LASER DOES NOT TURN ON
• Make sure batteries are installed according to (+), (-) markings on battery door.
• Make sure the batteries are in proper working condition. If in doubt, try installing new
batteries.
• Make sure that the battery contacts are clean and free of rust or corrosion. Be sure to keep the
laser level dry and use only new, high-quality batteries to reduce the chance of battery leakage.
• If the laser has been stored in extremely hot temperatures, allow it to cool.
THE LASER BEAMS FLASH
The DW083 laser level has been designed to self-level up to 4° in all directions when positioned
as shown in Figure 4. If the laser is tilted so much that internal mechanism cannot plumb itself,
it will flash the laser—the tilt range has been exceeded. THE FLASHING BEAMS CREATED BY
THE LASER ARE NOT LEVEL OR PLUMB AND SHOULD NOT BE USED FOR DETERMINING OR
MARKING LEVEL OR PLUMB. Try repositioning the laser on a more level surface.
THE LASER BEAMS WILL NOT STOP MOVING
The DW083 is a precision instrument. Therefore, if it is not positioned on a stable (and motionless)
surface, the tool will continue to try to find plumb. If the beam will not stop moving, try placing the
tool on a more stable surface. Also, try to make sure that the surface is relatively flat, so that the
laser is stable.
WALT accessories specified for
E
WALT, have not been tested with
E
WALT (1-800-433-
E
WALT service centers.
E
Measurement Between Marks
1/8" (3 mm)
1/16" (1.5 mm)
Measurement Between Marks
1/8" (3 mm)
1/4" (6 mm)
3/8" (9 mm)
Service and Repairs
NOTE: Disassembling the laser level will void all warranties on the product.
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by authorized service centers. Service or maintenance performed by unqualified
personnel may result in a risk of injury. To locate your nearest D
1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com.
E
Light Source
Laser Wavelength
Laser Power
Working Range
Accuracy* (Up)
Accuracy* (Level)
Indicators
Power Source
Operating Temperature
Storage Temperature
Environmental
*Accuracy spec assumes laser is positioned on a surface within 4° of level.
FIG. 1
A
WALT
E
FIG. 3
B
D
F
E
FIG. 5
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for three
E
years from the date of purchase. This warranty does not cover part failure due to normal wear or tool
abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.
com or call 1-800-4-D WALT (1-800-433-9258). This warranty does not apply to accessories or
E
damage caused where repairs have been made or attempted by others. This warranty gives you
specific legal rights and you may have other rights which vary in certain states or provinces.
In addition to the warranty, D
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
SPECIFICATIONS
Semiconductor laser diode
630–680 nm Visible
<1.5 mW (each beam) CLASS 2 LASER PRODUCT
±100' (30 m)
± 1/4" @ 100' (±6 mm @ 30 m)
± 1/4" @ 100' (±6 mm @ 30 m)
Flashing Indicator: battery low
Flashing Laser: tilt range exceeded
4 AA Size Batteries (6.0V DC)
20 °F to 120 °F (-10 °C to 50 °C)
-5 °F to 140 °F (-20 °C to 60 °C)
Water Resistant
FIG. 2
A
H
FIG. 4
G
>4°
C
FIG. 6
25'
(7.5 m)
FIG. 7
FIG. 8
FIG. 9
FIG. 10
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
WALT service center call
E
B
FLASHING
CLIGNOTANT
DESTELLA