Before Use - HIKOKI NT 65MA4 Instrucciones De Manejo

English

BEFORE USE

1. Check the air pressure
CAUTION
The air pressure must be constantly maintained at
4.9 – 8.3 bar (70 – 120 psi.).
Adjust the air pressure between 4.9 to 8.3 bar (70 –
120 psi.) according to the diameters and length of
nails and hardness of the wood being nailed. Pay
special attention to the output pressure, capacity,
and piping on the air compressor, so that air pressure
does not exceed the specified limit. Note that
excessive pressure may affect overall performance,
service life, and safety.
2. Lubrication
(1) Prior to operating this nailer, be sure to provide an air
set between the air compressor and this device.
Lubrication through the air set offers smooth
operation, extended service life, and anticorrosion.
Adjust the oiler so that a single drop of oil is supplied
at intervals of 5 to 10 nailing cycles.
(2) It is recommended using the recommended oil (SHELL
TONNA). Other applicable oils are listed. Never mix
two or more types of different oils.
3. Load nails
CAUTION
When loading nails into Nailer,
(1) do not depress trigger;
(2) do not depress push lever; and
(3) keep your face, hands feet and other body parts,
as well as those of other persons away from the
nose muzzle to avoid possible injury during usage
and carrying.
(1) Insert nail strip into rear of magazine (See Fig. 2).
(2) Slide the nail strip forward in the magazine.
The nail strip should pass the nail stopper.
(3) Pull the nail feeder (B) back to engage the nail feeder
(A) to the nail strip.
NOTE
Use nail strip of more than 5 nails.
The Nailer is now ready to operate.
Removing the nails:
1 Depress the nail feeder (A) slightly and slowly slide
the nail feeder (B) forward.
2 Remove the nails from the nailer.
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a
work bench on floor. Also, never face the nail outlet
toward any part of a person.
HOW TO USE THE NAILER
CAUTION
Never use the head or body of this device as a hammer.
Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Nailing procedures
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use SINGLE SEQUENTIAL ACTUATION MECHANISM
or CONTACT ACTUATION MECHANISM in accordance
with the work to be performed.
9
(1) Intermittent nailing
Set the switching device to the upward position (to set
to SINGLE SEQUENTIAL ACTUATION MECHANISM)
(See Fig. 3).
Depress the nail outlet onto the desired point; then
pull the trigger to drive a nail in a single shot (See
Fig. 4).
After nailing once, nailing will not be possible again
until the trigger is released and pressed again.
WARNING
A nail will fire each time the trigger is depressed as
long as the push lever remains depressed.
CAUTION
If you do not pull the trigger quickly and crisply while
in the single shot mode, the nailer will bounce and
shoot several nails instead of just one. To avoid this,
be sure to pull the trigger quickly and crisply.
(2) Push lever
When depressing the nail outlet, be sure to fully lift
the push lever (See Fig. 4) to release the safety lock.
Thus, nails cannot be driven without releasing the
safety lock even though the trigger is pulled.
(3) Continuous nailing
Set the switching device to the downward position (to set
to CONTACT ACTUATION MECHANISM) (See Fig. 5).
First, pull the trigger. Then depress the devise onto the
desired position to automatically drive nails (See Fig. 6).
The SINGLE SEQUENTIAL ACTUATION MECHANISM is
for use where precision fastener placement is desired.
The SINGLE SEQUENTIAL ACTUATION MECHANISM may
reduce the possibility of bodily injury to you or others in
the work area compared to the CONTACT ACTUATION
MECHANISM. This is because it is less likely to drive an
unwanted nail if you keep the trigger pulled and accidentally
bump the push lever against yourself or others.
The SINGLE SEQUENTIAL ACTUATION MECHANISM may
also reduce the speed of operation compared to the
CONTACT ACTUATION MECHANISM. The SINGLE
SEQUENTIAL ACTUATION MECHANISM is recommended
to inexperienced users.
CAUTION
Excercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
Do not drive a nail on another nail.
Do not drive a nail on metal parts.
NOTE
Precautions on no-load operation
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed "no-load operation". Such operation
may deteriorate the damper, magazine, and nail feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all
nails should be removed after using this nailer.
Always handle nails and package carefully. If nails
are dropped, collating bond may be broken.
After nailing:
(1) disconnect air hose from the nailer;
(2) remove all nails from the nailer;
(3) supply 5 – 10 drops of HiKOKI pneumatic tool
lubricant into the air plug on the nailer; and
(4) open the petcock on the air compressor tank to
drain any moisture.