Tabla de contenido
Idiomas disponibles
Idiomas disponibles
28 • ENGLISH
f Stay alert: Watch what you are doing. Use common
sense.
f Do not operate tool when you are tired.
f Maintain appliances with care: Follow instructions
in maintenance section. Inspect extension cords
periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
f Check damaged parts: Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by an authorized Service Center
unless otherwise indicated elsewhere in this manual.
f Keep the handles free from oil and fuel.
f Always use proper handles and shoulder strap
when cutting.
f Do not smoke while mixing fuel or filling tank.
f Always mix and store fuel in a properly marked
container that is approved by local codes and
ordinances for such usage.
f Never remove the fuel tank cap while the engine
is running.
f When ever approaching an operator of the machine,
carefully call his attention and confirm that the operator
stops the engine. Be careful not to startle or distract
the operator which can cause an unsafe situation.
f Never touch the nylon cutting head when ever the
engine is running. If it is necessary to adjust the
protector or nylon cutting head, be sure to stop the
engine and confirm that the nylon cutting head has
stopped running.
f The engine should be turned off when the machine is
moved between work areas.
f In strt-up or during operation of the engine, never
touch hot parts such as the muffler, the high voltage
wire or the spark plug.
f After the engine has stopped, the muffler is still hot.
Never place the machine in any places where there
are flammable materials (dry grass, etc.), combustible
gasses or combustible liquids.
f Pay specials attention to operation in the rain or just
after the rain as the ground may be slippery.
f If you slip or fall to the ground or into a hole, release
the throttle lever immediately.
f Wear no-slip heavy duty work gloves to improve your
grip on the brush cutter handle. Gloves also reduce
the transmission of machine vibration to your hands.
f Always stop the engine and remove the spark plug
wire before making any adjustments or repairs except
for carburetor adjustments.
f Mix and store fuel in a container approved for
gasoline. Do not smoke while fueling or mixing fuel.
f Mix fuel outdoors where there are no sparks or
flames. Wipe up any fuel spillage. Move 30 ft. away
from refueling site before starting engine.
f Stop the engine and allow to cool before refueling or
storing the unit.
f Allow the engine to cool; empty the fuel tank and
secure the unit from moving before transporting
in a vehicle.
SAFETY FIRST
Instructions contained in warnings within
this manual marked with a
concern critical points which must be taken
into consideration to prevent possible
serious bodily injury and for this reason you
are requested to read all such instructions
carefully and follow then without fail.
NOTES ON TYPES OF WARNING IN THE MANUAL
Warning! This mark indicates instructions which
must be followed in order to prevent accidents
which could lead to serious bodily injury or death.
Important! This mark indicates instructions which must
be followed, or it leads to mechanical failure, breakdown,
or damage.
Note: This mark indicates hints or directions useful in the
use of the product.
Warning! Never modify the product.We won't warrant
the machine, if you use the remodeled product or if you
don't observe the proper usage written in the manual.
SYMBOLS ON THE MACHINE
For safe operation and maintenance, symbols are shown
on the machine. According to these indications, please be
careful not to make a mistake.
(a)
(d)
PULL
CHOKE
RUN
a. The port to refuel the "GASOLINE MIX"
b. The port to top off the "CHAIN OIL"
c. Pull down the switch, stop the machine
d. Pull the choker rod, the choke close; push the choker
rod, the choke open
e. The position of H-needle
symbol
(b)
(e)
H
CHAIN OIL
L
MAX
T
(c)
(f)
MIN
Tabla de contenido
