Panasonic SC-UA7 Instrucciones De Funcionamiento página 18

"AUTO OFF"
• The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button or
touch any touch key.
"CAN'T REC"
•
You cannot do recording because the remaining recording
time of the USB device is less than the total time of the
music source. Change to a USB device which has enough
recording time and do the recording again.
•
You cannot do recording because the USB device is
write-protected. Remove the write protection of the USB
device and try again.
"DEVICE FULL"
•
You cannot do recording because the remaining recording
time of the USB device is less than the total time of the
music source. Change to a USB device which has enough
recording time and do the recording again.
"ERROR"
•
An incorrect operation was done. Read the instructions and
try again.
"ERROR" (during recording)
•
You cannot select other playback source (example: radio,
USB etc.) or press [2] or [6] during recording. Stop
the recording function.
"F61"
•
There is a problem with the amplifier of the system.
•
Disconnect the USB device. Switch off the system and then
switch on again.
"F703"
•
Examine the Bluetooth
•
Disconnect the Bluetooth
and then switch on again.
"F76"
• There is a problem with the power supply.
•
Disconnect the AC mains lead and consult your dealer.
"F77"
•
Disconnect the AC mains lead and consult your dealer.
"NO DEVICE"
•
You cannot do recording or check available storage space
because there is no USB device connected to
"NO PLAY"
"UNSUPPORT"
•
Examine the content. You can only play supported format.
• The files in the USB device can be corrupted. Format the
USB device and try again.
•
The system may have a problem. Switch off the system and
then switch on again.
"NO TRACK"
•
There is no album or track in the USB device or the internal
memory.
"PLAYERROR"
• An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REC ERROR"
•
You disconnected the USB device during recording.
Connect the USB device and do recording again.
•
An error occurred during USB recording. Disconnect the
USB device and then connect it again.
18
18
® connection.
® device. Switch off the system
USB B
"REMOTE 1"
"REMOTE 2"
•
The remote control and the unit are using different codes.
Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and
[1] for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and
[2] for a minimum of 4 seconds.
"TRK FULL"
•
The number of files has exceeded the supported limit.
"USB A NO DEVICE"
"USB B NO DEVICE"
•
The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
•
The USB device is using too much power. Disconnect the
USB device, switch off the system and then switch on
again.
"VBR"
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO/EXT-IN] to select "AUX 1" or "AUX 2".
█
To set the code to "REMOTE 2"
1
Touch and hold [SELECT] on the unit and [2] on
the remote control until "REMOTE 2" is shown.
2
Press and hold [OK] and [2] for a minimum of
4 seconds.
█
To set the code to "REMOTE 1"
1
.
Touch and hold [SELECT] on the unit and [1] on
the remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [1] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed or
when touch keys are touched.
• You want to clear and reset the memory contents.
1
Touch and hold [1] on the unit until "RESET?" is
shown.
2
While you touch and hold [1] on the unit, touch
[SELECT].
"RESET" is shown.
After "– – – – – – – – –" is shown, the unit will switch
off automatically.
All the settings are set back to the factory preset.
It is necessary to set the memory items again.